AcuRev 2100 Series Multi-Circuit Submeter With SnapOn CT Technology

Equipement décodé : ACCUENERGY - ACCUREV 2100 SERIES

Envoyez facilement une consigne en définissant uniquement la valeur, au lieu d’un downlink complet (payload + port)

ACCUENERGY

System Parameter Settings - Channel 1 Address

System Parameter Settings - RS485 Modbus Communication Parity Bit Setting

System Parameter Settings - Channel 2 Modbus Communication Parity

System Parameter Settings - RS485 Modbus Communication Baud Rate

1200-115200 When setting 115200, write?11520?

System Parameter Settings - Channel 2 Modbus Communication Baud Rate

System Parameter Settings - Password

System Parameter Settings - Energy Pulse Constant

System Parameter Settings - Energy Pulse Width

System Parameter Settings - Modbus TCP Device Address

System Parameter Settings - Energy Pulse Constant - High byte

0?Sliding Window 1?Rolling Window 2?Fixed Window 3?Thermal

System Parameter Settings - Demand Calculation Method

System Parameter Settings - Demand Interval

System Parameter Settings - Demand Sub-Interval

System Parameter Settings - CT Type

System Parameter Settings - RS485 Protocol Selection

System Parameter Settings - BACnet MS/TP Device Address

1200-115200 (When setting 115200, write 11520)

System Parameter Settings - BACnet MS/TP Baud Rate

System Parameter Settings - BACnet MS/TP Max Info Frames

System Parameter Settings - BACnet MS/TP BACnet ID - High byte

System Parameter Settings - BACnet MS/TP BACnet ID - Low byte

bit0~bit1 correspondsto RO1~RO2 0?Relay Control 1?Alarm

System Parameter Settings - Relay Output Mode

System Parameter Settings - RO Relay Control Output Mode

System Parameter Settings - RO Relay Control Momentary Time

System Parameter Settings - Alarm Enable

Bit0-bit9 corresponds to 1-10 1? Enable 0? Disable

System Parameter Settings - Alarm Channel Enable 1-10

Bit0-15 corresponds to 16 Event 1? Enable 0? Disable

System Parameter Settings - System Alarm Event

2 bytes, every 2 bits corresponds to an event 00 Relay1 01 Relay2

System Parameter Settings - Relay Output selection for first 8 System Alarm Events

22 bytes, every 2 bits corresponds to an event 00 Relay1 01 Relay2

System Parameter Settings - Relay Output selection for last 8 System Alarm Events

System Parameter Settings - Relay Output Alarm time delay

System Parameter Settings - Backlight Time

System Parameter Settings - Automatic Display if no key is pressed

System Parameter Settings - Screen Display Time per Screen

System Parameter Settings - Display power (demand) decimal places

System Parameter Settings - Reactive Power Calculation Method

System Parameter Settings - VAR/PF Convention

Set 1 to clear  Bit0: Clear current month  and historical electricity  Bit1: Clear demand  Bit2: Clear SOE record  Bit3: Clear the alarm record  Bit4: Clear the event record  Bit5: Clear the meter runtime  Bit6: Clear the battery runtime  Bit7: Reserved

System Parameter Settings - Clear all data digits to clear all records

838 address bit0~bit15 corresponds to DI1~DI16   839 address bit0~ bit1corresponds to DI17~DI18   0: No Clear  1: Clear

System Parameter Settings - The DI pulse count value is cleared, each bit represents one DI channel

Default 220V  0: 1LN  1: 3LN (Three-phase four-wire)   2:2LN(Single-phase three-wire)   3: 2LL   4: Network

System Parameter Settings - Rated voltage setting (Only relative to Alarm Setting)

System Parameter Settings - Wiring Mode

System Parameter Settings - Channel 1 CT Ratio

System Parameter Settings - Channel 2 CT Ratio

System Parameter Settings - Channel 3 CT Ratio

System Parameter Settings - Channel 4 CT Ratio

System Parameter Settings - Channel 5 CT Ratio

System Parameter Settings - Channel 6 CT Ratio

System Parameter Settings - Channel 7 CT Ratio

System Parameter Settings - Channel 8 CT Ratio

System Parameter Settings - Channel 9 CT Ratio

System Parameter Settings - Channel 10 CT Ratio

System Parameter Settings - Channel 11 CT Ratio

System Parameter Settings - Channel 12 CT Ratio

System Parameter Settings - Channel 13 CT Ratio

System Parameter Settings - Channel 14 CT Ratio

System Parameter Settings - Channel 15 CT Ratio

System Parameter Settings - Channel 16 CT Ratio

System Parameter Settings - Channel 17 CT Ratio

System Parameter Settings - Channel 18 CT Ratio

System Parameter Settings - Reset to Default (User name & mapping, wiring mode and CT type)

System Parameter Settings - Enable Ten Year Settings Download

Bit0: Communication  Parameters  Bit1: Network Parameters  Bit2: Device Run-Time  Bit3: Reserved  Bit4: Device Clock + TOU Related  Bit5: RO Related  Bit6: Device Clock

System Parameter Settings - Non-Standard Seal Options

System Parameter Settings - Seal Status

0: No output  1 to 18: Input channel 1 to 18  19 to 24: User channel 1 to 6  25: Incoming - System  26 to 28: Incoming - Phase A to C  29: Demand Indication   30: Second Indication  31 to 33: User channel 7 to 9 (for Network wiring only)

System Parameter Settings - DO1 Channel Setting

System Parameter Settings - DO2 Channel Setting

System Parameter Settings - DO3 Channel Setting

System Parameter Settings - DO4 Channel Setting

System Parameter Settings - DO5 Channel Setting

System Parameter Settings - DO6 Channel Setting

System Parameter Settings - DI Synchronous Demand Trigger Source

0: Do not trigger  1: Rising  2: Falling  3: Changing trigger

System Parameter Settings - DI Trigger Condition

8B9H: Bit0 to Bit16 (DI1 to DI6)  8BAH: Bit0 to Bit1 (DI17 to DI18)  0: State  1: Counter

System Parameter Settings - DDI Type

System Parameter Settings - DI1 to DI18 Counter Pulse Constant

System Parameter Settings - DI1 to DI18 Counter Ratio

System Parameter Settings - DI1 to DI18 Counter Unit

System Parameter Settings - Programming Button Status

Lock settings - Meter running time

Clock - Clock: Year

Clock - Clock: month

Clock - Clock: Day

Clock - Clock: hour

Clock - Clock: minutes

Clock - Clock: seconds

Clock - Clock: Week

Basic measurement - F

Basic measurement - Phase 1 Voltage

Basic measurement - Phase 2 Voltage

Basic measurement - Phase 3 Voltage

Basic measurement - Average Phase Voltage

Basic measurement - Line Voltage 1-2

Basic measurement - Line Voltage 2-3

Basic measurement - Line Voltage 3-1

Basic measurement - Average Line Voltage

Sum of the Phase A currents for all circuits on the meter

Basic measurement - Phase A inline Current

Sum of the Phase B currents for all circuits on the meter

Basic measurement - Phase B inline Current

Sum of the Phase C currents for all circuits on the meter

Basic measurement - Phase C inline Current

Average of the Phase A, Phase B and Phase C inline currents

Basic measurement - Average inline Current

Sum of Phase A, Phase B, and Phase C inline Real Power

Basic measurement - Total inline System Power

Sum of Phase A, Phase B, and Phase C inline Reactive Power

Basic measurement - Total inline Reactive Power

Sum of Phase A, Phase B, and Phase C inline Apparent Power

Basic measurement - Total inline Apparent Power

Average of Phase A, Phase B, and Phase C inline Power Factor

Basic measurement - Total inline Power Factor

Basic measurement - Total inline System Load Nature

ACCUENERGY - ACCUREV 2100 SERIES

nos produits

les + wattsense

votre besoin

La GTB pour piloter simplement les bâtiments de petite et moyenne taille.

nos produits

les + wattsense

ACCUENERGY
ACCUREV 2100 SERIES

Description

Spécifications

nos produits

les + wattsense

votre besoin

La GTB pour piloter simplement les bâtiments de petite et moyenne taille.

nos produits

les + wattsense

ACCUENERGYACCUREV 2100 SERIES

Description

Spécifications

ACCUENERGY
ACCUREV 2100 SERIES